What size of
ThermMAT for my room
ThermFloor offer a design service and will email a quick reply to any of your
enquiries.
First Step: Plan the installation.
Draw a general view of the room and mark the area which will be covered with
heating elements. Take measurements of the room. Avoid heating under units and
sanitary ware as this can cause heat blockage and it is unnecessary to heat
these areas anyway.
Make sure the ThermMAT can fit the floor area to be heated. It is better to
have just too little than too much over. NEVER cut the heating element.
Always start by measuring the FREE floor area available to apply the heat. In
a bathroom the FREE area is the floor area less the bath, shower, toilet and
washbasin etc. In a kitchen the FREE area is the floor area less the kitchen
units and appliances and so on.
Bear in mind to leave a minimum 50mm unheated gap around the room perimeter
when calculating the heated area.
You can combine more than one size of ThermMAT to cover the total floor
space. Each ThermMAT comes with a single 4m long cold lead wire at one end only,
and with multiple circuits the lead wires must be connected electrically in
parallel.
The chart below provides the installer with a wide selection of ThermMAT
sizes to suit the heated area. The chart is based on using either one size, or
two sizes wired together in parallel. Once the position for the control has been
decided the size of mat or combined sizes to match the room layout can be chosen
from the chart.
For example, for a heated floor area of 5mē you have the choice of using
ThermMAT sized at 5mē or a combination of 4mē + 1mē or 3mē + 2mē
Remember more than two mat sizes can be combined together if required.
ThermFloor systems are designed to match your heated floor space without
problems.
Click here to see available size
combinations.
Choose from the following Part
Numbers when you shop on-line
|
120 w/mē |
|
Part Number |
Area (mē) |
Width (m) |
Length (m) |
Total Watts |
Total Mat Resistance
(ohms) |
|
120MAT1 |
1 |
0.5 |
2 |
120 |
441 |
|
120MAT15 |
1.5 |
0.5 |
3 |
180 |
294 |
|
120MAT2 |
2 |
0.5 |
4 |
240 |
220 |
|
120MAT3 |
3 |
0.5 |
6 |
360 |
147 |
|
120MAT4 |
4 |
0.5 |
8 |
480 |
110 |
|
120MAT5 |
5 |
0.5 |
10 |
600 |
88 |
|
120MAT6 |
6 |
0.5 |
12 |
720 |
73 |
|
120MAT7 |
7 |
0.5 |
14 |
840 |
63 |
|
120MAT8 |
8 |
0.5 |
16 |
960 |
55 |
|
120MAT9 |
9 |
0.5 |
18 |
1080 |
49 |
|
120MAT10 |
10 |
0.5 |
20 |
1200 |
44 |
|
160 w/mē |
|
160MAT1 |
1 |
0.5 |
2 |
160 |
331 |
|
160MAT15 |
1.5 |
0.5 |
3 |
240 |
220 |
|
160MAT2 |
2 |
0.5 |
4 |
320 |
165 |
|
160MAT3 |
3 |
0.5 |
6 |
480 |
110 |
|
160MAT4 |
4 |
0.5 |
8 |
640 |
83 |
|
160MAT5 |
5 |
0.5 |
10 |
800 |
66 |
|
160MAT6 |
6 |
0.5 |
12 |
960 |
55 |
|
160MAT7 |
7 |
0.5 |
14 |
1120 |
47 |
|
160MAT8 |
8 |
0.5 |
16 |
1280 |
41 |
|
160MAT9 |
9 |
0.5 |
18 |
1440 |
37 |
|
160MAT10 |
10 |
0.5 |
20 |
1600 |
33 |
|
